Control Module Power Supply

• 105-130 VAC @ 15A, single phase, 47-63 Hz
• 210-260 VAC @ 7.5A, single phase, 47-63 Hz (optional)
• Operating temperature: 0-50° C
  
  The MTS-3030 Two Convertible Channels Module, MTS-3040 AC Voltage Module and MTS-3060 AC Current Module receive power from and are controlled by the MTS-3000 Control Module. The system will operate down to 90 VAC with reduced voltage and current outputs. For some configurations the 15A/7.5A rating may be exceeded if all outputs are at full power. Maximum voltage and current specifications are given for nominal 120/240 VAC input at 20° C ambient temperature. Ratings may be reduced with lower input voltage and higher ambient temperature.

Output Frequency

• Power Line, frequency and phase locked
• Variable
• 8.000 - 99.999 Hz (0.001 Hz resolution, 0.01% accuracy)
• 100 - 499.99 Hz (0.01 Hz resolution, 0.02% accuracy)
• 500 - 1000 Hz (0.1 Hz resolution, 0.02% accuracy)
• Two independently variable frequencies are available

Time Measurement

• Measures interval from either fault initiation or an external start trigger signal
• 0 - 99999 sec, auto-ranging scale
• 0 - 99999 cycles, auto-ranging scale
• Resolution: 0.1 ms/ 0.1 cycles
• Accuracy: +/- 0.5ms, +/- 1 digit
• Two wire pulse timing mode

Programmable States

• Pre-fault and Fault

Operational States

• Pre-fault, Fault (2 modes), Breaker Opening, Post Fault and Breaker Closing

Phase Control

• Phase angle of all AC outputs adjustable from 0 to 360°
• Setting resolution: 0.1°
• Accuracy: +/- 0.5°

Harmonics

• Single harmonic, 2nd through 10th , maximum harmonic frequency = 1000 Hz
• Harmonic amplitude 0 - 50% of fundamental

Static/Dynamic Testing Capabilities

• Phase to ground, phase to phase and three phase faults
• Two phase to ground faults
• Phase, frequency, voltage and current stepping
• Phase, frequency, voltage and current ramping with adjustable ramp rates
• Programmable auto-reclose time delay and reclose-into-fault events
• Programmable breaker opening and closing times
• Fault incidence angle control (point-on-wave)

Communication/Control

• Two RS-232 serial ports, for equipment under test and for remote control, with programmable communication parameters and flow control
• Parallel output port for printing test results

Control Module:

• 15"W x 7.5"H x 11 5/8"D (38.1cm W x 19cm H x 29.5cm D)
• Weight: 18 lbs. (8.2 kg)
• Built-in side carry handles
• Dimensions & weight include top and bottom covers

Options

Control Module Options:
MTS-3010 Programmable Digital I/O Module with trigger channels
MTS-3020 DC Voltage Module (Maximum configuration: 1 per Control Module.)
Option 09 240 VAC operation for Control Module

System Features

• Hard-shell shipping case with casters
  25.75"W x 23.25"H x 17.25"D (65.5cm x 59cm x 44cm) Weight: 35.5 lbs. (16.1 kg)
• Protective front cover (optional)
• Operation and Reference Manual
• 1 year warranty
  
  Full 3-phase system weight:
  Weight with control module, 3 voltage and 3 current channels, top and bottom covers and the protective front cover - 69.8 lbs. (31.7kg).

  3 Module Stack:
  15"W x 18.75"H x 12.75"D (38.1cmW x 47.6cmH x 32.4cmD – Including protective cover adds 1 1/8"D (2.9cmD)
  (Height of assembled stack is less then the total of 3 modules)

  System Options:
  Option 01 Heavy Duty Shipping Case
  Option 02 Test Lead Kit
  Option 03 Extra Manual
  Option 04 Additional 1 Year extended warranty
  Option 05 DC Current Module (MTS-3010 required)
  Option 06 Additional AC Voltage Channel
  Option 07 Additional AC Current Channel
  Option 09 240 VAC operation for CM (must be used with options 29, 49 & 69)

MTS-3010 Digital I/O Module
This optional module installs in the Control Module case and is used to provide timing functions and to supply DC current to the device(s) under test.

• 2 Programmable inputs
  NC or NO wet/dry contact inputs, 300VDC/AC maximum, fully isolated
  Start/Stop trigger inputs for fault initiation/termination
  Audible and visual indication of state of 1st input
  Programmable contact de-bounce delay, 0.1 - 999.9 msec, 0.1 msec resolution
• 1 Programmable auxiliary contact output, fully isolated
  5A @ 300VAC, 1A @ 125VDC, 0.5A @ 250VDC, 0.35A @ 300VDC resistive load
  Breaker signal (52A/52B) simulation
  Permissive/unblock signal simulation with programmable delay, 0 - 9999.0 msec, 0.1 msec resolution.

MTS-3020 DC Voltage Module
This optional module installs in the Control Module case and maybe used to supply auxiliary power to the device(s) under test.

• DC voltage output 0-300 VDC @ 100W maximum
• Setting resolution: 0.1V
• Accuracy greater of 1% of setting or 0.75V
• Current Limit: 2A, fully short circuit proof

MTS-3040 AC Voltage Module

• 3-phase wye voltage
• 0-150V rms phase to neutral, direct coupled
• 125VA maximum per channel (high range 75-150V), P.F.=1.0
• 100VA maximum per channel (low range 0-75V), P.F.=1.0
• Setting resolution: 0.01V
• Accuracy: greater of 0.25% of setting or 0.1V rms
• Fully open & short circuit proof and thermal overload protected

• 15"W x 6.25"H x 11 5/8"D (38.1cm W x 15.9cm H x 29.2cm D)
• Weight with 3 channels: 23.2 lbs (10.5 kg)

Option 06 Additional AC Voltage Channel
Option 42 AC Voltage Test Lead Kit
Option 49 240 VAC operation

Maximum configuration: 3 Channels per Module, 2 Modules per stack.

MTS-3060 AC Current Module

• Direct coupled
• Fully open & short circuit proof and thermal overload protected
• Setting resolution: 0.001 Amps rms
• Accuracy: greater of 0.25% of setting or 0.005A rms

• 0-25A rms maximum, 15V rms maximum
• 0-12A rms maximum, 30V rms maximum
• 275VA maximum

• 0-75A rms maximum
• 600VA maximum @ 35A
• 300VA maximum @ 75A

• 0-25A rms maximum per channel

• 15"W x 6.25"H x 11 5/8"D (38.1cm W x 15.9cm H x 29.2cm D)
• Weight with 3 channels: 28.8 lbs. (13.1 kg)

Option 07 Additional AC Current Channel
Option 62 AC Current Test Lead Kit
Option 69 240 VAC operation

Maximum configuration: 3 Channels per ACI Module, 2 Modules per stack.